RGB Accessories
![Smart T](https://minleonusa.com/wp-content/uploads/2021/04/Smart-Ts-w-NDB-1663x500.jpg)
RGB Accessories such as spacer cables, T-ways and power injector supplies are needed to customize and efficiently run your lighting displays. Please refer to the guidelines described in our "RGB Accessory" and "Power & Data Management" video tutorials, or contact support@minleonusa.com.
![](https://minleonusa.com/wp-content/uploads/ACC7V2CRMain-500x300.png)
Mounting Clips
Mounting accessories for Minleon C9, C7 and similarly sized retrofit bulbs, and RGB+ strings.
Learn More![Basic T](https://minleonusa.com/wp-content/uploads/2020/10/Basic-T-500x300.jpg)
Basic T
Back feed power to WEC+ or split a light string to run in parallel. Not intended for general inline power injection.
Learn More![Spacer Cables – 3-wire](https://minleonusa.com/wp-content/uploads/2020/10/RGBSpacer-500x300.jpg)
Spacer Cables – 3-wire
For use between the RGB controller and first light, or for use between light strings or fixtures.
Learn More![Extender Cables – 4-wire](https://minleonusa.com/wp-content/uploads/2021/04/RGB50-4w-500x300.jpg)
Extender Cables – 4-wire
Long 4-wire spacer cables to extend the data signal. For use only between Data Boosters.
Learn More![Data Boosters](https://minleonusa.com/wp-content/uploads/2020/04/RGBDataBoosters-500x300.jpg)
Data Boosters
Essential to maintain the LED data signal for RGB+ cable runs of approximately 20-feet or greater. Sold as a pair, the Sender converts 3-wire light strings to 4-wire for use with 4-wire Extender Cables. The Receiver then converts the 4-wire back to 3-wire for the next power injection or light run.
Learn More![Smart T](https://minleonusa.com/wp-content/uploads/2021/04/Smart-T-chain-500x300.jpg)
Smart T
Smart T's give individual control of RGB strings. Add strings to each NDB output, or add outputs to the WEC+2.
Learn More![Power T](https://minleonusa.com/wp-content/uploads/2020/04/RGBPowerT-500x300.jpg)
Power T
Inline power injection T-way after 100L or 100-feet (12V strings), whichever comes first, or 180-200L with 24V strings. Isolates power forward, to prevent crossing voltage in the installation.
Learn More![5A-12V transformer](https://minleonusa.com/wp-content/uploads/2021/04/RGB5A-12v-500x300.jpg)
5A-12V transformer
Power up to 100, 12V dual RGB-LED pixels, at 12" spacing, or 125-feet at pitches less than 12". Will also power larger 12V lamps in lesser quantities.
Learn More![3A-24V transformer](https://minleonusa.com/wp-content/uploads/2020/10/RGB3A-24v-500x300.jpg)
3A-24V transformer
For the Rainmin RGB product lines, power up to 180, dual RGB-LED 24V pixels. Will also power larger lamps in less quantities and distance. Use inline in a single direction with Power T. Or power a WEC with a Basic T, back-feeding power to the controller while you power forward to the lights. Do not cross voltage-RGB-LEDs do not like to receive power from both directions, and this will decrease their lifespan and potentially cause data latency.
Learn More![4A-24V transformer](https://minleonusa.com/wp-content/uploads/2020/10/RGB4A-24v-500x300.jpg)
4A-24V transformer
For the Rainmin RGB product lines, power up to 200, dual RGB-LED 24V pixels, across 200-feet. Will also power larger lamps in less quantities and distance.
Learn More![4-Wire Adapters](https://minleonusa.com/wp-content/uploads/2021/04/RGB4w-Adapter-RGB2-500x300.jpg)
4-Wire Adapters
For the new RGB+2 DoubleDATA strings. Connect to any WEC or NDB output port. Then set your controller's configuration to RGB+2.
Learn More